Tiếng Anh
Tiếng Đức, tiếng Đức
Tiếng Ả Rập, tiếng Ả Rập
Tiếng Pháp, tiếng Pháp
Tiếng Indonesia (tiếng Việt)
Tiếng Nhật
Tiếng Hàn / tiếng Hàn
Tiếng Mã Lai
Tiếng Bồ Đào Nha, tiếng Bồ Đào Nha
Tiếng Nga, tiếng Nga
Tiếng Tây Ban Nha, tiếng Tây Ban Nha
Tiếng Thái (tiếng Thái)
Tiếng Thổ Nhĩ Kỳ, tiếng Thổ Nhĩ Kỳ
Tiếng Việt / tiếng ViệtHiện tại
Reinforced Frame
An aluminum-alloy or galvanized-steel perimeter frame provides defined edges and supports additional internal reinforcement where fixtures or openings are planned.
Hệ thống tường và trần phòng sạch
Bảng điều khiển phòng sạch thủ công
A manually assembled cleanroom sandwich panel designed for projects that need non-standard dimensions, reinforced fixing points, equipment openings or special edge details. Its framed construction supports flexible core, facing and interface configurations.
- Custom openings and cutouts
- Reinforced perimeter frame
- Project-specific core options
- Flexible non-standard modules
Custom-Built for Complex Cleanroom Interfaces
Handmade cleanroom panels are assembled around a reinforced perimeter frame rather than formed as a continuous production strip. This construction method is suited to project-specific modules, service penetrations, door and window interfaces, embedded supports and other details that are difficult to accommodate with a standard panel.
Factory-Prepared Openings
Cutouts for windows, pass boxes, utility panels, electrical boxes and equipment interfaces can be prepared from approved drawings before delivery.
Non-Standard Modules
Panel width, length, thickness and edge details can be adapted for irregular rooms, renovation work and areas with dense service coordination.
Selectable Core System
Rock wool, glass-magnesium composites, honeycomb and polymer insulation cores can be selected according to structural, thermal and project requirements.
Concealed Fixing Support
Internal plates or reinforcing members can be positioned for wall-mounted equipment when loads and fixing locations are confirmed during design.
Replaceable Modular Construction
Framed modules and dry installation methods support local access, modification or panel replacement during future cleanroom upgrades.
Customer Problems It Helps Solve
The panel is intended for projects where standard factory modules cannot fully resolve openings, loads or non-standard interfaces.
On-site cutting creates dust and damaged edgesOpenings can be fabricated from coordinated drawings, reducing uncontrolled cutting and allowing the frame and edge finish to be prepared before installation.
Wall-mounted equipment lacks reliable fixing pointsSpecified internal reinforcement can be added behind the facing at known fixture locations, subject to load review and approved shop drawings.
Standard modules do not fit irregular room geometryCustom dimensions and edge configurations help close non-standard bays, refurbishment zones and technical wall interfaces.
One core specification cannot serve every roomCore, facing and thickness options can be selected by zone to balance fire, thermal, acoustic, hygiene and budget priorities.
Các ứng dụng điển hình
Suitable for customized cleanroom envelope areas and locations that require coordinated openings or embedded support.
Pharmaceutical Production SuitesBiotechnology LaboratoriesHospital Clean AreasElectronics FacilitiesFood Packaging RoomsTechnical Wall SystemsPass Box and Window InterfacesCleanroom Renovation Projects
Thông số kỹ thuật
The following values describe common configurable ranges for handmade cleanroom panels. Final dimensions and performance depend on the selected core, facing, frame, joint and project drawings.
| Panel Construction | Manually assembled framed cleanroom sandwich panel |
|---|---|
| Common Module Width | 980 mm or 1180 mm; standard and non-standard widths available by project |
| Common Thickness | 50 mm, 75 mm or 100 mm; other framed configurations available after review |
| Panel Length | Custom manufactured; wall panels are commonly supplied up to 6000 mm subject to handling and transport limits |
| Facing Options | Pre-painted galvanized steel, stainless steel or HPL-faced construction where specified |
| Typical Metal Facing Thickness | 0.5-0.8 mm depending on material, span, finish and project requirement |
| Frame Options | Cold-drawn aluminum-alloy or galvanized-steel perimeter frame; localized internal reinforcement optional |
| Core Options | Rock wool, glass-magnesium rock wool, magnesium-based board, aluminum honeycomb, paper honeycomb, PU or EPS |
| Joint Options | Male-female interlock or center-aluminum connection with sealant-ready cleanroom joint |
| Custom Fabrication | Openings, service panels, electrical boxes, inspection access, embedded plates and special edge preparation |
| Installation | Cleanroom wall or ceiling systems; support spacing and load capacity confirmed by engineering review |
| Performance | Fire, thermal, acoustic and load performance are configuration-dependent and confirmed against project requirements |
Important: Submit coordinated drawings before production. Opening locations, concentrated loads, suspension points and required test documentation must be confirmed for the selected panel assembly.
How to Specify a Handmade Panel
1. Map Every Interface
Provide panel layouts with doors, windows, pass boxes, utilities, electrical boxes and equipment penetrations clearly dimensioned.
2. Define Loads and Performance
Identify fixture loads, ceiling access needs, fire targets, cleaning chemicals, temperature and acoustic requirements.
3. Approve the Shop Drawings
Confirm module size, core, facing, frame, reinforcement, joint direction and opening details before fabrication begins.
Need custom openings or reinforced fixing points?
Send us your panel schedule, opening dimensions, fixture loads and required core material.
